Back
Universal Repeater 300 | REPEATER300V2
How can I connect my device to my Universal Repeater 300 for the installation?
Wi-Fi connection to Universal Repeater 300. The factory default Wi-Fi network name is STRONG_2.4GHz and there is no password.
How can I change the settings?
You can change all the settings by the web management interface embedded in the product. The URL of the web management interface is http://strong.ap300
The URL (http://strong.ap300) does not work for the installation, I cannot access to web management interface.
For installation only, please use http://192.168.10.1 to access to web management interface.
What is the IP address of Universal Repeater 300?
I installed my Universal Repeater 300 as a repeater, it works perfectly but I cannot access to http://strong.ap300. How can I access to web management interface of Universal Repeater 300?
What is the default username and password of web management interface?
Username: admin
Password: admin
I don’t find my existing Wi-Fi network in Installation wizard of the Universal Repeater 300?
Universal Repeater 300 might be located too far away from your modem/router. It is recommended to put it in the same room with the modem/router for the installation, and then you can move it to another place by checking that at least 2 of the Wi-Fi signal LEDs are still green.
What is the best location for the Universal Repeater 300 as a repeater?
Please place your Universal Repeater 300 in the middle, between your Gateway/Router and the location that lacks Wi-Fi coverage where there are at least 2 of the Wi-Fi signal LEDs are green.
I installed Universal Repeater 300 in repeater mode. Can I use a different Wi-Fi network name and password than my Wi-Fi router?
Yes. Please follow the Repeater Wizard during the installation. You can also change the Wi-Fi network name by “Basic Settings” menu on the web management interface after the installation.
How can I install Universal Repeater 300 as an Access Point?
Please ensure that the Mode Selection switch at the side panel of your Universal Repeater 300 is at Access Point mode.
Do a factory reset by keeping pressed the “Reset” button for 6 seconds if your product is configured as a Repeater or Router earlier.
Connect your modem/router by an RJ45 Ethernet cable to the WAN/LAN port of the Universal Repeater 300.
Connect your Wi-Fi device to one of the default Wi-Fi network (STRONG_2.4GHz) provided by Universal Repeater 300. There is no password for the default Wi-Fi network.
Login to the web management interface of Universal Repeater 300 by the URL http://strong.ap300 , click on “AP Wizard” and follow the steps.
How can I install Universal Repeater 300 as a Router?
Please ensure that the Mode Selection switch at the side panel of your Universal Repeater 300 is at Router mode.
Do a factory reset by keeping pressed the “Reset” button for 6 seconds if your product is configured as a Repeater or Router earlier.
Connect your modem/router by an RJ45 Ethernet cable to the WAN/LAN port of the Universal Repeater 300.
Connect your Wi-Fi device to one of the default Wi-Fi networks (STRONG_2.4GHz and STRONG_5GHz) provided by Universal Repeater 300. There is no password for the default Wi-Fi networks.
Login to the web management interface of Universal Repeater 300 by the URL http://192.168.10.1 , click on “Router Wizard” and follow the steps.
Which Wi-Fi frequencies (bands) does Universal Repeater 300 provide?
Universal Repeater 300 is a single band 2.4GHz device.
Which frequencies are used to create connection between the router/modem and Universal Repeater 300?
Universal Repeater 300 can create a connection to your modem/router on 2.4GHz band and it repeats the Wi-Fi signal of your modem/router on 2.4GHz.
Can I change the Wi-Fi channels of Universal Repeater 300 at repeater mode?
Yes, you can change the channel of the Wi-Fi band that is not being used for the communication between your modem/router at “Basic Settings” menu on the web management interface.
I have a guest network on my modem/router. Can I extend my router's guest network as well as the main Wi-Fi network with a Universal Repeater 300?
No. Universal Repeater 300 can only repeat one Wi-Fi network. You need to select the Wi-Fi network that you want to extend during the installation of Universal Repeater 300.
I use MAC address filtering rules configured on my router. Can I use Universal Repeater 300 to extend the Wi-Fi network of my modem/router in this case?
Yes, you can, but you need to allow the MAC addresses (MAC Address and 2.4 GHz BSSID) of Universal Repeater 300 at the MAC address filtering settings of your router. The MAC addresses (MAC Address and 2.4 GHz BSSID) of Universal Repeater 300 can be found at the “Device Status” section on its web management interface (http://strong.ap300)
Will the MAC address-filtering settings configured on my modem/router be effective if I use Universal Repeater 300 to extend the Wi-Fi network of my modem/router?
No. Wi-Fi devices that are connected to Universal Repeater 300 communicate to your modem/router by using the MAC addresses of Universal Repeater 300.
How can I set my Universal Repeater 300 to factory defaults?
Please keep the Reset button gently pressed (for instance using a paperclip) at the back panel of your Universal Repeater 300 until the LEDs get flashing.
I installed my Universal Repeater 300 as a Repeater but there is only one Wi-Fi LED is on.
Please move your Universal Repeater 300 to a closer location to your modem/router to have a better performance.
I installed my Universal Repeater 300 as a Repeater but my broadband Internet speed is not improved, why?
Repeaters can improve the Wi-Fi coverage, performance and connectivity locally but the broadband Internet speed is defined by your subscription of your Internet Service Provider.
